COMPAQ

[Гост]

Някой може ли да ми каже как се влиза в BIOS-а на стар COMPAQ (клавишна комбинация) ?

Благодаря предварително.

[Pepon]

Probvai s F10

Usually works!

[Гост]

Не става.

[Pepon]

Pri starite Compaq BIOS-a e zapisan na HDD. Shtom F10 ne raboti znachi e iztrit ot tam. Triabva da se izpolzuva BIOS setup disketta. Prati mi modela i shte se opitam da ti pomogna s neshto.

[gerchev]

Напиши модела или поне някакви подробности за hardware . Tака по лесно ще можем да ти помогнем.
Процесора на колко MHz e. или поне това което можеш да напишеш.
Ще потърся из моите архиви неща такова.

[gerchev]

Toва което го пише Pepon e taka Compaq FAQ: How do I access the

Rom Bios (CMOS) setup of my Deskpro EN, EP, EP-SB, 6000, 4000, 2000, 4000s, 4000n, and ProSignia 300 Desktop computers? (FAQ5473)
F10 Bios-Cmos Setup
(see models list below)
F10 Computer Setup/VP and PC Diagnostics Pentium Pro & MMX models
http://www.compaq.com/support/files/des ... d/263.html

Text Help File for F10 Setup for non-MMX PCI Models
ftp://ftp.compaq.com/pub/softpaq/sp8001-8500/sp8126.txt

Personal Computer Diagnostics
http://www.compaq.com/support/files/des ... /9260.html

Readme Text file for Personal Computer Diagnostics
ftp://ftp.compaq.com/pub/softpaq/sp1600 ... p16085.txt

The F10 computer (ROM Bios) setup utility for this model normally resides on the hard drive on a special partition. Pressing the F10 key during boot when the cursor flashes in the upper right of the display/monitor will bring up this utility. If this does not happen, then the utility is damaged or is not installed.

Then it would be necessary to download the F10 setup file from the Compaq Internet site to the hard drive of this or some other computer. Execute the executable file and read the instructions or read the associated Text/Help file shown above. The result will be one or more bootable disk that can be used to boot the computer into the Bios setup utility. This Setup boot disk can be used any time that the computer Bios/Cmos setup needs to be changed. The special F10 partition can be restored to the hard drive to restore use of the F10 key to activate it. To do this would require the disk drive to be cleaned by running Fdisk and Format and starting over with the drive (this would remove all data from the drive). This is usually not worth it to simply have the ability to press the F10 key to run the setup when it can be run at any time by booting to the bootable setup disk.

The next time the drive is rebuilt or if it is replaced, then the utility can be added at that time. To do this, remove all partitions from the drive and then boot to the bootable setup disk. The utility will recognize that there are no partitions on the drive and ask if it is the intention to install the F10 partition. If this question is answered with yes to this then the partition will be created. The computer will reboot and install the utility (if the setup disk was left in the A:\ drive).


Family Models
Deskpro EN Series P266, P300, P300A, 6300C, P333, 6333C, P350, P400, 6400C, P450, P450+, P500, P550, P600, P650, P700

Deskpro EN SFF Series P300, P300A, 6300C, P333, 6333C, P350, P400, P450, P450+, P500, Net PC P300, Net PC P400, P650, P700

Deskpro EP Series P266, 6266C, P300, P333, P350, P400, P650, P700

Deskpro SB Series P266, P300, P333, P350, P400

Deskpro 6000 5166, 5200, 6180, 6200, 6233MMX, 6233X, 6266MMX, 6266X, 6300MMX, 6333

Deskpro 4000N 5166MMX, 5200MMX, 5233MMX

Deskpro 4000S 5166MMX, 5200MMX, 5233MMX

Deskpro 4000 5100, 5120, 5133, 5166, 5166MMX, 5200, 5200MMX, 5233MMX, 6180, 6200, 6233MMX, 6233X, 6266MMX, 6300MMX, 6333

Deskpro 2000 5166MMX, 5200MMX, 5233MMX, 6233MMX, 6266MMX, 6300MMX

Prosignia 330 P350, P400

Prosignia 310 P300A, P333, 6366C, 6400C

Не знам какъв е модела при теб.


Ако не изтегли си от тук за по старите PC -ta

http://h18007.www1.hp.com/support/files ... /7106.html

[Гост]

Благодаря ти, gerchev, но Рероn ми помогна вече. COMPAQ вече е в действие. Много се готини, благодаря ви още веднъж. При пръв удобен случай ще черпя